日本思达（CEDAR)扭力起子_详细资料

产品信息

见详细说明

The trap of management of torque

When it is going to bolt a screw by a power driver etc., output torque is inspected by the torque tester for power drivers.

This is required for the performance management of a power driver.

However, this value is not a torque value which is a value which shows the output of a driverhas become tight.

Managing torque truly is managing "the torque value of the actually tightened screw."

However, the tester which measures "the torque value of the actually tightened screw" till today did not exist.

I manufactured this machine in order to solve it.

- The check of "the torque value of the actually tightened screw" by a user''s product random inspection

- Ask for the relation between "the value of a torque circuit tester","the torque value of the actually tightened screw". The output torque of a power driver is set upmanaged.

SLIP TORQUE DETECTOR DI-12

DI-12-SL4

Measuring range 0.030 - 4 N丒m
For the screws of M2.5 - M5
(Torque within measuring range)

DI-12-SL02 DI-12-SL15

Measuring range 1.5 - 200 mN丒m
For the screws of M2 or less
(Torque within measuring range) Measuring range 0.30 - 15 N丒m
For the screws of M6 - M8
(Torque within measuring range)

丂丂

Measuring method

Change of the point which increases, performs a bundle examinationis slid from a firm point is caught,a torque value is judged.

Smooth bundle lump work is done by motor drive.

A motor is stopped if it judges. It increasesmany exaggerated torque to a bundle examination is prevented. It loosens,fastens at the time of torque inspection,there is no necessity for repair work.

丂丂丂丂Specification

Form			DI-12-SL4	DI-12-SL02	DI-12-SL15
Operating range			0.030乣4.000丂N丒m丂	1.5乣200.0丂mN丒m	0.30乣15.00丂N丒m
accuracy			亇1% (500 or less digit亇5digit)	亇0.5% (200 or less digit亇1digit)
Display丂			The 4 figures digital display of LCD
The measurement direction			CW-CCW (rightleft)A display will be the display of only an absolute value. Load of + (the CW direction)- (the direction of CCW) is carried out to a data output.
Measure-ment Mode	P-P(peak)		The peak load value hold.Destructive torque (the CW direction) －－ it loosenstorque (the direction of CCW) is measured.
	T-R(truck)		A display changes with load change.
	PD judging mode		The judgment of slide torquethe judgment of the yield point are performed. (Only the CW direction)
Detection judging			If a slide torque value is detected, you will be told about by green lamp lighting.(at the time of RG mode)
Measurement start value setup			The value which starts measurement (start of judgment operation) is set up. ( 0.001 N-m unit from 0 N-m)
Continuation data output			A load torque value is outputted for every fixed time during measurement in RG mode. By creating a torque wave, loci, such as slide torque, yield point torque,destructive torque, can be judged.
Auto-power-off			Automatically power off after 5 minutes left without operation
Bit plug form			HEX丂6.35	fai 4丂	6.35sq
Data output			ASCII format丂(baud rate 9600). A measurement result is outputted.
Outside dimension		Detector	fai 44亊190丂Other projection thing	fai 20亊145丂	fai 55亊270丂
		Indicator	166(W)亊142(D)亊48(H)
Weight丂		Detector	About 820g丂	About 80倗	About 1.5k倗
		Indicator	About1kg
Accessories (one piece each)			Bit丂亄丂#1丂#2	Bit丂亄丂#0
			An inspection report, a proofreading certificate, a traceability system figure

信息声明：本产品供应信息由仪器网为您整合，供应商为（苏州伟创精密仪器有限公司），内容包括（日本思达（CEDAR)扭力起子）的品牌、型号、技术参数、详细介绍等；如果您想了解更多关于（日本思达（CEDAR)扭力起子）的信息，请直接联系供应商，给供应商留言！

供应商产品推荐

DI-12-SL4

Measuring range 0.030 - 4 N丒m For the screws of M2.5 - M5 (Torque within measuring range)
DI-12-SL02	DI-12-SL15

Measuring range 1.5 - 200 mN丒m For the screws of M2 or less (Torque within measuring range)	Measuring range 0.30 - 15 N丒m For the screws of M6 - M8 (Torque within measuring range)