抗震网架橡胶垫块厂家

抗震网架橡胶垫块厂家

网架橡胶垫块是由多层橡胶片硫化粘合而成一种普通橡胶支座产品，这种产品具有足够的竖向刚度，能够将支座上部构造的反力可靠的传递给墩台，支座具有良好的弹性，以应对桥梁的梁端的转动；又有较大的剪切变形能力，以满足上部构造的水平位移。
The grid rubber pad is composed of multilayer rubber sheet and a vulcanized rubber bearings products, this product has enough vertical stiffness, can force reliable transfer to the pier upper bearing structure, bearing has good flexibility, in response to the bridge beam end rotation; and a larger shear the deformation ability, to meet the horizontal displacement of superstructure.
网架橡胶垫块的布置主要和桥梁的结构形式有关：
The layout of the rubber pad of the grid is mainly related to the structure of the bridge.
通常在布置支座时需要考虑以下的基本原则：
The following basic principles should usually be taken into consideration in the arrangement of support:
1、上部结构是空间结构时，橡胶垫块应能同时适应桥梁顺桥向（X方向）和横桥向（Y方向）的变形；
1. When the superstructure is a spatial structure, the rubber pad should be able to adapt to the deformation of the bridge direction (X direction) and the transverse bridge (Y direction).
2、橡胶垫块必须能可靠的传递垂直和水平反力；
2, rubber padding blocks must be able to reliably transfer vertical and horizontal forces.
3、橡胶垫块应使由于梁体变形所产生的纵向位移、横向位移和纵、恒向转角应尽可能不受约束；
3. The rubber cushion block should make the longitudinal displacement, the lateral displacement and the longitudinal and constant angle due to the deformation of the beam body as far as possible.

抗震网架橡胶垫块厂家
4、当桥梁位于平坡上，固定橡胶垫块宜设在主要行车方向的前端桥台上；
4. When the bridge is located on the flat slope, the fixed rubber pad should be located on the front end abutment of the main driving direction.
5、橡胶垫块宜设置在具有较大垫块反力的地方；
5, the rubber pad should be set in a place with large counterforce.
6、在同一桥墩上的几个橡胶垫块应具有相近的转动刚度；
6. Several rubber padding blocks on the same pier should have similar rotational stiffness.
总之，橡胶垫块的布置原则是既要便于传递支座反力，又要使橡胶垫块能充分适应梁体的自由变形。
In a word, the arrangement principle of the rubber pad is not only to transfer the back force of the bearing, but also to make the rubber pad fully fit the free deformation of the beam.
网架橡胶垫块的安装：
The installation of the rubber pad for the net frame:
1、在垫块安装之前应对支座的安装位置进行测量检验，支座安装平面应和支座的滑动平面或滚动平面平行，其平行度的偏差不宜超过2‰。
1, before installing the cushion blocks, we should measure the installation position of the bearing. The bearing installation plane should be parallel to the sliding plane or rolling plane of the bearing, and the deviation of parallelism should not exceed 2 per thousand.
2、垫块安装前应对活动支座顶、底板的相对位置进行检查。
2, before the installation of the pad, the relative position of the top and floor of the movable support should be checked.
3、垫块安装后，滚动和滑动平面应水平，其与理论平面的斜度不大于2‰。支座上、下板ZX应对中，其偏差不大于2‰。
3. After the padding block is installed, the rolling and sliding plane should be horizontal, and the slope of the plane is not more than 2 per thousand with the theoretical plane. The deviation of the upper and lower plate centers is not more than 2 per thousand.
4、为保证垫块安装平整，一般应在支座底面与职称垫石顶面之间，捣筑20～50mm厚的干硬性无收缩砂浆垫层。
4. In order to ensure the smooth installation of the pad, the dry and hard shrinkage mortar cushion of 20 to 50mm thick should be mashed between the bottom of the support and the top of the title stone.