介绍KTR带轴联轴器，KTR联轴器资料

介绍KTR带轴联轴器，KTR联轴器资料
SYNTEX? is a safety system operating with positive locking suitable for torques up to 525 Nm. The component transmitting the torque is a punched disk spring (protected by patent). The design of the coupling ensures short reaction times with high repeating accuracy.  Due to the special design it is easy to integrate the coupling in the drive.

大型机器设备调整两轴对中较困难，应选择使用耐久和更换易损件方便的联轴器。金属弹性元件挠性联轴器一般比非金属弹性元件挠性联轴器使用寿命长。需密封润滑和使用不耐久的联轴器，必然增加维护工作量。对于长期连续运转和经济效益较高的场合，例如我国冶金企业的轧机传动系统的高增端，目 前普遍采用的是齿式联轴器，齿式联轴器虽然理论上传递转矩大，但必须在润滑和密封良好的条件下才能耐久工作，且需经常检查密封状况，注润滑油，维护工作量大，增加了辅助工时，减少了有效工作时间，影响生产效益。
Torque limiters and overload systems which re-engage automatically should only be used with a reduced speed for higher release torques. Frequent or longer slipping or ratching increases the wear of the torque limiter.
KTR联轴器工作环境
联轴器与各种不同主机产品配套作用，周围的工作环境比较复杂。对于高温、低温、有油、酸、碱介质的工作环境，不宜选用以一般橡胶为弹性元件材料的挠性联轴器，应选择金属弹性元件挠性联轴器。 弹性柱销齿式联轴器由于运转时柱销的窜动，自身噪声大，对于噪声有严格要求的场合不应选用。

介绍KTR带轴联轴器，KTR联轴器资料
制造、安装、维护和成本
在满足便用性能的前提下，应选用装拆方便、维护简单、成本低的联轴器。例如刚性联轴器不但结构简单，而且装拆方便，可用于低速、刚性大的传动轴。一般的非金属弹性元件联轴器(例如弹性套柱销联轴器、弹性柱销联轴器、梅花形弹性联轴器等)，由于具有良好的综合能力，广泛适用于一般的中、小功率传动。
Overload system in combination with backlash-free ROTEX? GS
Backlash-free and torsionally-stiff
Axial plug-in
Low mass moment of inertia
Different elastomer hardness degrees available
We basically recommend electronic monitoring of the torque limiters in order to protect the drive in case of overload.
We will be pleased to support you with technical questions and with the selection of torque limiters. For that purpose we dispose of the latest simulation and calculation programs. Here the following fact applies: The more detailed the data, the more accurate are the calculation results.
After the torque limiter has disconnected driving and driven side in case of overload, it may take some time before the drive comes to standstill because of a high inertia in the drive train. This may cause higher wear on the torque limiter and the overload system re-engaging automatically. That is why we recommend the use of the overload system KTR-SI as an idle rotation type for drives with big inertias or with higher speeds.