JCNR-A 厂家直销建筑材料难燃性试验仪热卖

建筑材料难燃性试验仪     

编号：GD201311030064

规格：JCNR-A

产品名称：建筑材料难燃性试验仪

产品型号：JCNR-A

主要用途：

建筑材料难燃性试验仪适用于确定一种材料是否具有难燃性。试验装置包括燃烧竖炉和控制仪器等。

建筑材料难燃性试验机 

符合GB/T8625、DIN4102《建筑材料难燃性试验方法》，在规定的条件下判定建筑材料是否具有难燃性，凡是经过燃烧竖炉试验合格并能通过建筑材料可燃性试验的材料均可定为难燃性建筑材料。

本方法的试验装置主要包括燃烧竖炉及控制仪表两部分

一、建筑材料难燃性试验仪试验装置:

1、燃烧竖炉：燃烧竖炉主要由燃烧室、燃烧器、试件支架、空气稳流器及烟道等部分组成。其外形尺寸为1 020mm×1 020mm×3 930mm。

2、燃烧室：燃烧室由炉壁和炉门构成，其内空尺寸为800mm×800mm×2 000mm。炉壁为保温夹层结构，炉门分为上、下两门，分别用铰链与炉体连接，其结构与炉壁相似。两门借助手轮和固定螺杆与炉体闭合。在上炉门和燃烧室后壁设有观察窗。

3、燃烧器：燃烧器水平置于燃烧室ZX，距炉底1 000mm处。

4、试件支架：试件支架为高1 000mm的长方体框架，框架四个侧面设有调节试件安装距离的螺杆，框架由角钢制成.

5、空气稳流器：空气稳流器为一角钢制成的方框，设置于燃烧器下方。方框底部铺设铁丝网，其上铺设玻璃纤维毡。

6、烟道：燃烧竖炉的烟道为方形的通道，其截面积为500mm×500mm，并位于炉子顶部，下部与燃烧室相通，上部与外部烟囱相接。

二、建筑材料难燃性试验仪控制仪表：

燃烧竖炉的控制仪表包括流量计、热电偶、温度记录仪及温度显示仪表等。

1、流量计：甲烷气和压缩空气所用流量计，甲烷为6~60L/MIN可调，空气为3~30L/MIN可调。

2、热电偶：烟道气温度和炉壁温度的测定均采用精度为Ⅱ级，外径不大于3mm的镍铬—镍硅铠装热电偶。

3、温度记录仪及显示仪表：温度记录仪采用精度为0．5级的可连续记录的电子电位差计；温度数字显示仪的精度为±0．5％土一个字。两种仪表与热电偶配套并用。

 Building materials burning tester

Number: GD201311030064

Specification: JCNR-A

Product Name: building materials burning tester

Product type: JCNR-A

Main uses:

Building materials burning tester was applied to determine whether a material is hard to burn. The test device comprises a combustion furnace and control instrument.

Difficult flammability for building materials testing machine

According to GB/T8625, DIN4102 "building materials difficult flammability test method", to determine whether the building material is hard to burn under stipulated conditions, usually through the combustion furnace test and by building materials flammability test materials can be difficult flammability for building materials.

=============================================================

The test device of the method mainly comprises a combustion furnace and control instruments part two

A flame test equipment, building materials tester:

1, the combustion furnace: combustion furnace is composed of a combustion chamber, a burner, specimen bracket, air regulator and flue components. Its size is 1 020mm × 1 020mm × 3 930mm.

2, the combustion chamber: the chamber formed by the furnace wall and the furnace door, the inner space size is 800mm × 800mm × 2 000mm. Furnace wall heat preservation sandwich structure, the door is divided into the upper, two doors, and the furnace body is connected by hinges, and the structure of the furnace wall similar. Two door by hand wheel and the fixed screw and the furnace body is closed. In the door and the combustion chamber wall is provided with an observation window.

3: burner, burner level in the center of the combustion chamber, from the bottom 1 000mm.

4, the specimen holder: specimen bracket is a cuboid frame height of 1 000mm, four side frames is provided with a regulating specimen installation distance of the screw, the frame is made of angle steel

5, air regulator: air regulator for angle steel box, is arranged on the burner. The box at the bottom of the laying of barbed wire, which laying glass fiber mat.

6: the burning furnace flue, flue is square channel, the cross section of 500mm * 500mm, and is located in the top of the furnace, the lower part is communicated with the combustion chamber, the upper and external chimney.

Two, building materials burning tester control instrument:

The combustion furnace control instruments including meter, thermocouple, temperature recorder and temperature display instrument.

1, the flowmeter flowmeter: methane gas and compressed air, methane is 6~60L/MIN adjustable, adjustable air 3~30L/MIN.

2, the thermocouple: Determination of flue gas temperature and wall temperature of the gasifier are used in precision for grade II, outside diameter less than 3mm nickel chromium - nickel silicon thermocouple.

3, temperature recorder and display instrument: temperature recorder with precision of 0.5 level can continuously record the electronic potential difference meter; digital temperature display meter with an accuracy of ± 0.5% soil a word. Two kinds of instruments and facilities and thermocouple.

亲：

1.可免费为客户检测试样；

2.可以根据不同客户的需求进行订做产品。

3.售前，我们专门派技术人员为您设计Z佳的流程和方案；

4.信后，将免费指派技术人员为您调试安装；

5.保修一年，产品终身维护；

6.常年供应设备的易损件及耗品，以确保产品长期使用。

北京冠测试验仪器有限公司专注于试验方法的创新及应用，是集研发、生产、销售、售后于一体的专业试验仪器供应商！

咨询洽谈业务!