AC WITHSTAND VOLTAGE |
| Range | Resolution | Accuracy |
Output Voltage, ACV | 0-5000 | 1 | ?(2% of setting 5V) |
Output Frequency | 50Hz/60Hz ?100ppm, User Selection |
Output Waveform | Sine Wave ,THD.<2% (Resistive Load), Crest Factor = 1.3 - 1.5 |
Output Regulation | ? (1% of output 5V), From no load to full load |
SETTINGS |
Maximum Limit current, mA | 0.000 - 9.999 (0=OFF) | 0.001 | ? (2% of setting 2 counts) |
10.00-30.00 | 0.01 |
Minimum Limit current, mA | 0.000 - 9.999 (0=OFF) | 0.001 | ? (2% of setting 2 counts) |
10.00-30.00 | 0.01 |
Ramp-Up Timer, second | 0.1 - 999.9 | 0.1 | ? (0.1% 0.05 sec) |
Ramp-Down Timer, second | 0.0 - 999.9 |
Dwell Timer, second | 0, 0.4 - 999.9
(0=continuous) |
Arc Detection | 1 - 9 ranges (9 is the most sensitivity) |
DC WITHSTAND VOLTAGE |
Output Voltage, DCV | 0-5000 | 1 | ?(2% of setting 5V) |
Output Ripple | <4 %（5KV/10mA at Resistive Load） |
SETTINGS |
Maximum Limit, current, 礎 | 0 - 999.9 | 0.1 | ? (2% of setting 2 counts) |
1000 - 10000 | 1 |
Minimum Limit, current, 礎 | 0.0 - 999.9 | 0.1 | ? (2% of setting 2 counts) |
| 1000 - 10000 | 1 |
Ramp-Up Timer, second | 0.1 - 999.9 | 0.1 | ? (0.1% 0.05 sec) |
Ramp-Down Timer, second | 0, 1.0 - 999.9 (0=OFF) |
Dwell Timer, second | 0, 0.4 - 999.9
(0=continuous) |
Ramp-HI, current | >12 mA peak maximum, ON/OFF User Selection |
Charge-LO, current | 0.0 - 350.0 礎 DC or Auto Set |
Discharge Time | < 200 msec |
Maximum Capacitive LoadDC Mode | 1 礔 < 1KV 0.08 礔 < 4KV |
0.75 礔 < 2KV 0.04 礔 < 5KV |
0.5 礔 < 3KV |
Arc Detection | 1 - 9 ranges (9 is the most sensitivity) |
INSULATION RESISTANCE |
Output Voltage, VDC | 50 - 1000 | 1 | ? (2% of setting 2 counts) |
Short Circuit Current | Maximum >12mA peak |
SETTINGS |
Maximum and Minimun Limit
Resistance, MΩ | 0.05 - 99.99(Max – Limit: 0 = OFF) | 0.01 | Same as Resistance MEASUREMENT Accuracy |
100.0-999.9 | 0.1 |
1000-50000 | 1 | ? (0.1% 0.05 sec) |
Ramp-Up Timer, second | 0.1 - 999.9 | 0.1 |
Ramp-Down Timer, second | 0, 1.0 - 999.9 (0=OFF) |
Delay Timer, second | 0, 1.0 - 999.9
(0=continuous) | 0.1 |
Charge-LO, current, 礎 | 0.000 - 3.500 or Auto Set |
MEASUREMENT |
| Range | Resolution | Accuracy |
Voltage, KV (AC/DC) | 0.00-5.00 | 0.01 | ? (1.5% of reading 2counts) |
Voltage, Vdc (IR only) | 0-1000 | 1 | ? (1.5% of reading 2counts) |
AC Current, mA | 0.000-3.500 | 0.001 | ? (2% of reading 2counts) |
3.00-30.00 | 0.01 |
DC Current, 礎 | 0.0 - 350.0 | 0.1 | ? (2% of reading 2 counts) |
DC Current, mA | 0.300 - 3.500 | 0.001 |
3.00-9.99 | 0.01 |
Resistance, MΩ | 50-499V | 500-1000V | | 50 – 499V
0.05–999.9, ?(7% of reading 2 counts) |
0.050-1.999 | 0.050-9.999 | 0.001 | 500 – 1000V |
2.00-19.99 | 10.00-99.99 | 0.01 | 0.10–999.9, ?(2% of reading 2 counts) |
20.0-199.9 | 100.0-999.9 | 0.1 | 1000–9999, ?(5% of reading 2 counts) |
200-50000 | 1000-50000 | 1 | 10000–50000, ?(15%of reading 2 counts) |
GENERAL |
Input Voltage | 115/230Vac?15% Auto Selection, 50/60Hz ? 5%, Fuse 4A Slow-Blo 250VAC |
PLC Remote Control | Input: Test, Reset, Interlock, Recall Memory 1 through 10 |
Output: Pass, Fail, Test-in-Process, Reset Out |
Remote Output Relays | 125VAC@1AAC, 30VDC@ 0.DC |
Memory | 50 memories, 30 steps/memory |
Graphic Display | 240 x 64 dot resolution Monographic LCD /Contrast 9 Levels 1-9 |
Safety | Built-in Smart GFI circuit,GFI trip current 450礎 max, HV shut down speed: <1mS |
Interface | Standard RS232, Optional Printer Port with Date and Time Stamp or GPIB (IEEE-488.2). |
Security | Programmable password lockout capability to avoid unauthorized access to test set-up program. |
Alarm Volume Setting | Range: 0-9 ;0=OFF, 1 is softest volume, 9 is loudest volume. |
Calibration | Adjustments are made through the fornt panel. Built-in Verification program. |
Automatic Calibration alert function to signal operator when calibration is due. |
Environment | 0-40℃, 20-80%RH |
Dimensions/Net Weight | (W ? H ? D) 2U (430 ? 89 ? 400 mm)/13Kg. |
Option (Opt.735) | DC Continuity Test Function (0.1A/ 0-2KΩ) at Rear Panel |
STANDARD ACCESSORIES |
Power Cord(10A) | ?1 |
Fuses | ?2 (Including a spare contained in the fuse holder) |
Interlock Disable Key(1505) | ?1 |
Hipot Test Lead ,1.5m(1101) | ?1 |
Hipot Return Lead ,1.8m(1102) | ?1 |
RS232 Link Cable 1.5m(1130) | ?1 |
MATRIX SCANNER MODULE (Opt.729) |
High Voltage Rating | 5KVAC/5KVDC |
Number of HV Channel | 8 |
MATRIX SCANNER MODULE (Opt.730) |
High Voltage Rating | 5KVAC/5KVDC |
Number of HV Channel | 4 |
DC CONTINUITY TEST FUNCTION (Opt.735) |
MEASUREMENT |
| Range | Resolution | Accuracy |
Output Current | DC 0.1A ? 0.01A, Max. |
Resistance Display | 0.00 – 19.99 | 0.01 | ? (1 % of reading 5 counts) |
20.0 – 199.9 | 0.1 | ? (1 % of reading 2 counts) |
200 – 2000 | 1 | ? (1 % of reading 2 counts) |
SETTINGS |
Max-Limit, Ω | 0.00 – 19.99 | 0.01 | ? (1 % of setting 5 counts) |
20.0 – 199.9 | 0.1 | ? (1 % of setting 2 counts) |
200 – 2000 | 1 | ? (1 % of setting 2 counts) |
Min-Limit, Ω | 0.00 – 19.99 | 0.01 | ? (1 % of setting 5 counts) |
20.0 – 199.9 | 0.1 | ? (1 % of setting 2 counts) |
200 – 2000 | 1 | ? (1 % of setting 2 counts) |
Dwell Timer, second | 0.0, 0.3 – 999.9
(0 = continuous) | 0.1 | ? (0.1% 0.05 sec) |
Resistance Offset, Ω | 0.00 – 2.00 | 0.01 | ? (1 % of reading 5 counts) |
