深圳GGB探针代理商，森东宝代理美国GGB系列探针，原装进口
- 型号：12C系列
- 产地：中国大陆
- 供应商：深圳市森东宝科技有限公司
- 供应商报价：电议
- 标签：深圳GGB探针代理商，森东宝代理美国GGB系列探针，原装进口,光学仪器,配件耗材,供应深圳GGB探针代理商，森东宝代理美国GGB系列探针，原装进口,深圳市森东宝科技有限公司
产品库
The PICOPROBE® MODEL 12C is a high speed, high input impedance active probe for measuring the internal node voltage of integrated circuits. The input is 1 megohm shunted by 0.1 pf ａnd the rise/fall times are 0.8 ns. This instrument has full dc capability ａnd can be used with any oscilloscope. The Model 12C was specially designed so that when used in conjunction with a high input impedance oscilloscope, signal attenuation is 10:1 ａnd with a 50 Ohm input, signal attenuation is 20:1.
Rugged, dependable ａnd high speed the Model 12C presents a very modest load to the integrated circuit. It can be used to troubleshoot high speed bipolar, NMOS ａnd CMOS circuits-even some short holding time dynamic nodes. Each amplifier is individually optimized for peak performance ａnd reliability. The Model 12C will withstand large input over voltages. The only known failure mode is the accidental breaking or crushing of the probe tip which can be easily replaced. A large selection of replaceable probe tips are available to accommodate a variety of probing needs.
Specifications
Input Capacitance 0.1pf Input Resistance 1.0 megohm Rise/Fall Time 0.8ns Bandwidth dc to 500 MHz Linearity 0.5% Voltage Range -10 to +20V* Gain Accuracy ±3% Signal Attenuation (High Input impedance oscilloscope: 10 to1) (50 ohm input: 20 to 1) FIGURE 2
| Picoprobe® Model 12C Replacement Tips | |||
|---|---|---|---|
Part Number |
Shaft Diameter |
| |
| 12C-1-5 | 5 micron | <0.1 micron |  |
| 12C-1-10 |
|
| |
| 12C-1-22 |
|
| |
| 12C-1-35 |
|
| |
| 12C-1-60 |
|
| |
| 12C-1-125 |
|
| |
| 12C-2-5 | 5 micron | <0.1 micron |  |
| 12C-2-10 |
|
| |
| 12C-2-22 |
|
| |
| 12C-2-35 |
|
| |
| 12C-2-60 |
|
| |
| 12C-2-125 |
|
| |
|
| |||
| 12C-4-5 | 5 micron | <0.1 micron |  |
| 12C-4-10 |
|
| |
| 12C-4-22 |
|
| |
| 12C-4-35 |
|
| |
| 12C-4-60 |
|
| |
| 12C-4-125 |
|
| |
| FIGURE 3 |
The Model 12C replacement tip slides easily in ａnd out of the Model 12C Picoprobe® body. The replacement tip consists of a housing, a precision resistor/capacitor combination, ａnd a tungsten probing wire that is tapered to a fine point. The tungsten wire allows ample flexing so the probe point ａnd the circuit remain in contact even in the presence of probe table vibrations. The flexible wire even reduces the potential for damage to the circuit ａnd probe point. Replacement tips are available with 10, 22, 35, 60, ａnd 125 micron diameter wires which are sharpened as indicated in the table above.*Special order Model 12C PICOPROBES® are available for -15V.
Requires the use of a Picoprobe® Power Supply. Please specify 110V or 220V when ordering.
